SITC of 315 KVA Transformer and other Electric work at Udyog Bhawan, Jaipur.

PWD - CE AND AS / ACE - AJMER / SE-AJMER / EE-DIST-AJMER · Jaipur, Rajasthan · Electrical Equipment & Supplies · open

Key facts

Tender value: ₹11.4L
EMD: ₹23K
Published: 02 Nov 2026
Closing date: 12 Nov 2026
Status: open
Status as of: 04 Nov 2026 04:42 UTC
Ministry: Government of Rajasthan
Department: Public Works Department
Office: Executive Engineer, P.W.D. Electric Division-I, Jaipur

Description

Supply, installation, testing and commissioning of a 315 KVA transformer and associated electrical works at Udyog Bhawan, Jaipur, including cables, earthing, distribution equipment, wiring and related civil work. Completion period is 4 months from issue of work order.

Eligibility & requirements

Startup relaxation: No
MSE relaxation: No
Certifications: Transformer and electrical equipment test certificates as specified, CPRI type test certificates for temperature rise test, short circuit test for 50 kA and IP test
Documents required: Valid license from Electric Inspector, Test reports of items from the concerned manufacturer, if required, Final as-built drawing, Handed-over inventory list, Approved GA drawing of panel before fabrication

New to these terms? Read how tender eligibility criteria work.

Commercial terms

Bid type: Percentage
Evaluation: Percentage rate tender; one percentage rate for all items of the schedule
Make in India (MII): No
MSE preference: No

Line items (29)

2 — Qty: 3 4
Providing & Laying XLPE insulated & P.V.C. sheathed Armoured Aluminium cable confirming to IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing commissioning etc. as required of following size.400.0 Sq. mm.3.5 core — Qty: 30 Mtr
Providing & making heat shrinkable type indoor/outdoor/straight through terminations/ joint kit suitable for 11 KV / 33 KV (Earthed) cable with required components, prepration of cable ends. Type test report should be as per IS13573:2011 including testing etc. as required of following sizes. 11 KV End Termination Kit Indoor type 3 core 120/150/185 Sq.mm — Qty: 2 Each
Providing & making heat shrinkable type indoor/outdoor/straight through terminations/ joint kit suitable for 11 KV / 33 KV (Earthed) cable with required components, prepration of cable ends. Type test report should be as per IS13573:2011 including testing etc. as required of following sizes. 11 KV Straight Through Joint Kit . 3 core 120/150/185 Sq.mm — Qty: 1 Each
SITC of Copper Bonded rod Earthing with high tensile strength (more than 600 N / sq.mm low carbon steel rod molecularly bonded with Copper thickness (250 microns) and confirming to UL 467 of following size and length and as per point mentioned (a), (b), [c), (d), (e) below :- (a) Bore a hole of dia. 100 mm of required length, Place the rod in the centre of Hole (b)Earth enhancing compound to ensure the moisture content and electrical conductivity, 25 kg for 3000 mm. The compound shall be tested form NABL accredited lab for low resistivity (less than 0.12 Ohm - meter) & high conductivity in nature with carbon as a major content in accordance with IEC 62561-7 (c) Connect the rod with copper Strip/Conductor/Wire with suitable clamp made from tinned copper and SS 304 Bolt (d) Place Heavy duty weather proof poly-propylene earth inspection chamber as per requirement of IS/IEC 62305 and tested as per IEC 62561-5 with lockable Jam free lid suitable for safe working load 60 kN of round / square — Qty: 4 Set
Supply & Laying following size earth strip in horizontal or vertical run in surface by means of Earth strip DMC Insulator including riveting/ soldering/ welding, Jointing shall be done by overlapping double the width of strip and with 2 set of Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at 50cm making connection etc. as required.25mm x 3mm G.I. ( Hot Dipped ) Strip — Qty: 10 Mtr.
Supply & Laying following size earth strip in horizontal or vertical run in surface by means of Earth strip DMC Insulator including riveting/ soldering/ welding, Jointing shall be done by overlapping double the width of strip and with 2 set of Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at 50cm making connection etc. as required.25mm x 3mm copper strip — Qty: 10 Mtr.
Providing & Fixing of Heavy duty capacitor start, copper wound Double ball bearing 900/1400 RPM single phase Exhaust fan conforming to IS:2312 marked in existing opening including making connections testing etc. as required. 300 mm sweep(900 RPM) — Qty: 1 Each
Providing & Fixing of Wall mounting / Pedestal type Heavy duty Air Circulator , Double ball bearing and with metal sturdy mesh guard; Aluminium alloy one piece blade and conforming to IS:2997, including fixing with anchor bolts, making connection testing etc. as required. 450 mm sweep Wall mounting and three speed regulator with Minimum Air Delivery 150 Cum. / Minute — Qty: 4 Each
S I T C of star rated Aluminium wound distribution Transformer of following rating 11/0.433KV Delta-Star Connected, Vector Group Dyn 11,ONAN Cooled & as per BEE star - 1 ( Correspnding level as per BIS amended upto date of receipt of tender) & BIS approved as per IS 2026- 1977 & losses as defined as per 2014 (Fourth Revision) Level-1 including standard accessories like conservator, silica gel breather, radiator, fins, HT cable box & LT cable boxes, temperature rise in winding/oil 35-40 degree C upto 200 KVA & 40-45 degree C for above 200 KVA, ISI marked drain valve, Dial type Temperature gauge, first filling of transformer oil as per IS :335-1953, Epoxy based paint, undirectional rollers as required including carrying of pre-commission Testing & Charging of Transformer complete in all respect . (On Existing RCC foundation/Steel Structure) Factory Tests: The Transformer shall be subjected to routine factory tests (as per IS:2026 and IS:1180) and Following tests shall be carried out on e — Qty: 1 Set
Supply & fabrication steel structure with MS channel / angle / joist / ISMB / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamel paint etc. as required complete in all respect. . — Qty: 50 Kg
Earth work in excavation/ by mechanical means (Hydraulic Excavator) / Manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sum on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed: — Qty: 4 cum
Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with Cement Mortar 1:6 ( 1-Cement : 6-Sand). — Qty: 5 cum
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level .1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) — Qty: 6 cum
Plaster on new surface on wall in cement sand mortar 1:4 including racking of joints etc. complete fine finish : 12mm thick — Qty: 12 Sqm
Providing Manpower through Contracting agency for Supervision / Execution / Operation of various Electromechanical Installations. (one shift of 8 working Hrs per day ) on basis of minimum wages + VDA order Dt. 28.03.2025 Ministry of Labour and Employement Govt. of India.Technical Helper Having basic Knowledge of E&M Services — Qty: 20 Each per Day
Supplying and laying FR PVC insulated & unsheathed flexible copper conductor of following nominal sizes with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. 1 x 1.5 sq.mm — Qty: 40 Mtr.
Supplying and laying FR PVC insulated & unsheathed flexible copper conductor of following nominal sizes with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. 1 x 4.0 sq.mm — Qty: 40 Mtr.
Supplying and laying FR PVC insulated & unsheathed flexible copper conductor of following nominal sizes with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. 1 x 6.0 sq.mm — Qty: 40 Mtr.
Supplying and laying FR PVC insulated & unsheathed flexible copper conductor of following nominal sizes with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. 1 x 10.0 sq.mm — Qty: 40 Mtr.

2 tender document(s) available — sign up to download.

Related tenders

SUPPLY OF V.F TRANSFORMER OF RATIO 470:600 OHMS (CYLINDER TYPE) — Electrical Equipment & Supplies · Madhya Pradesh
Handheld Rechargeable Pocket Torch — Electrical Equipment & Supplies · Madhya Pradesh
Procurement of Digital Dial Indicator and Stainless Steel Flexible Magnetic Base stand — Electrical Equipment & Supplies
Erection of lighting line for mine lighting purpose at R-VI seam and various places coal depot, DDU, Agent office at Khottadih OCP — Electrical Equipment & Supplies · West Bengal · ₹9.9L
Procurement of Electrical instruments/Equipments and machinery for Electrical, Repairing, Fabrication and other electrical works at Gumgaon Mine — Electrical Equipment & Supplies · Maharashtra · ₹1.9L
Work of re-organisation of generator line in different rooms of Bankola Area offiece. — Electrical Equipment & Supplies · West Bengal · ₹1.5L
Diversion of 6.6KV O/H Line at Jharna Face due to increase in water level and widening of Haul Road for feeding power to 4000GPM Motor Pump in SOCP Muraidih AMP Colliery. — Electrical Equipment & Supplies · Jharkhand · ₹1.2L
Installation of earth pits at different substations of Jambad Colliery — Electrical Equipment & Supplies · West Bengal · ₹5.1L