Repair and Maintenance of High mast and repair of existing street light infrastructure under Electrical sub Division No.2 Chandigarh

Engineering-MCC · Chandigarh · Electrical Equipment & Supplies · open

Key facts

Tender value: ₹5.0L
EMD: ₹10K
Published: 28 Sep 2026
Closing date: 05 Oct 2026
Status: open
Department: Municipal Corporation
Office: Electrical Division

Description

Eligibility & requirements

Startup relaxation: No
MSE relaxation: No

New to these terms? Read how tender eligibility criteria work.

Commercial terms

Bid type: Open Tender
Evaluation: Percentage
Make in India (MII): No
MSE preference: No

Line items (20)

S/E of CC Collars including following:- The box shall be enclosed in a cement collar made from cement concrete 1:2:4 with outside dia 16”. The collar shall be embedded in the group upto 6” shall stand 9” above ground shall have housed 12” high SMC Box and 6” top over the box. The collar shall be provided with 2 G.I. Pipe of 40mm dia and 45cm long to facilitate entry of cables in the junction box after digg out the cable loops from earth complete in all respects, connections etc. The collar shall be plastered properly finished, curing and painted with 2 coats of Apex paint of superior quality. Providing and Fixing junction box of size 250x200x100mm inside dimensions of thermosetting sheet moulding compound material of robust construction with double hinge, side clamp locking arrangement. The existing ckt cable loops be made properly connection after digging from the earth and refilling the same position. There should be a terminal Strip (Thimble type) 30 amp, one no. Kitkat, rating suitable for minimum 4x16 sq.mm aluminum cable termination. The sheath of the armoured cable should be properly thimbed with the pole for proper earthing. Curing of CC Collar must be done as per satisfaction of Engineer-in-charge. The junction box should have two numbers PVC Glands with sufficient space for cable entry and loose wires complete in all respect. — Qty: 98 Nos.
Providing and fixing of Junction Box Cover of Fiber Sheet of 10"x8" suitable size on existing octagonal pole/ Street Light Poles. The fiber cover shall be installed on existing jucntion box with the help of screw. The job includes the cost of all labour charges and other petty material required to complete the job upto entire satisfaction of Engineer-in-Charge. — Qty: 100 Nos.
Dismantling and re-erection of 16/12.5 Mtr high mast with the help of Crane. The work shall be executed as per the entire satisfaction of Engineer in Charge — Qty: 2 Nos.
The stainless steel wire ropes shall be in AISI 316 grade, 7/19 construction with central core in the same material of diameter and the breaking load of rope shall not be less than 2x2350 Kg, giving a factor of safety of over 5 for the system at full load as per the TR7 reffered to in the beginning of this specification. The work shall be executed to the entire satisfaction of Engineer-in-Charge. — Qty: 120 Mtr
Supply & laying PVC insulated Aluminium Conductor armoured ISI Marked cable of 5 Core 2.5mm sq in Trench/Pipe. Supply & laying of ISI marked 5 core 2.5 mm sq PVC Insulated Aluminium conductor armoured cable of make Havells/ Finolex/ Ecko/ Lapp/ Cirtina/ Sunhome/ Polycab/ KEI/ Panasonic conforming IS:1554 (Pt.1) amended. The cable shall be laid as per DSR Code 7.1 MV CBPIP (external). The work shall be executed as per the entire satisfaction of Engineer in Charge — Qty: 30 Mtr
Supply and erection of lubrication/greasing/oil in gear box. The work shall be executed as per the entire satisfaction of Engineer in Charge — Qty: 15 Nos.
Whinching of High mast of 16/12.5 mtr.The work shall be executed as per the entire satisfaction of Engineer in Charge — Qty: 1 Nos.
Dismantling of existing damaged/broken old bollard lights/CC Collar, Jallies alongwith junction box, wire and C.C. foundation etc. and other material complete in all respect to the satisfaction of Engg-in-charge. The entire “malba” shall be disposed off and send to C & D plant Industrial Area Phase-I. The work shall be executed as per the entire satisfaction of Engineer in Charge — Qty: 30 Nos.
Painting of pedestal size 1200x900x350mm with P.O. red paint complete in all respect and bonding to the existing earth etc. and platform of cement concrete 1:2:4 around the pillar box of size 3’x2’x0’-4”. The Cost includes writing MCC and Danger in Bold letters such that it is warning about hazard as threats which are essential to safety for General Public. — Qty: 50 No
Supply & laying of ISI marked 4 core 16 mm sq PVC Insulated Aluminium armoured cable loose in trench/pipe:- Supply & laying of ISI marked 4 core 16 mm sq PVC Insulated Aluminum conductor armoured cable (PVC Sheathed) of make Sunhome/ Finolex/ Cirtina/ Ecko/ Lapp/ Polycab/ KEI conforming IS:1554 (Pt.1) amended. The cable to be laid in trench/ pipe as per DSR Code 7.5.1/2022 MV CB PIP-25 Part-II (External). The cable should be terminated existing/ new cc collar with proper thimbling. The job included all Connections, Commissioning and testing of phase supply Material Testing report to be submitted and material to be supplied at site after confirmation from Engineer-in-charge. The specification of the cable as below:- i) Conductor – Aluminum ii) Core – 4 iii) Working Voltage – 1100 V iv) Nominal Cross Section – 16mm2 v) Minimum No. of Wire – 7/6 vi) Insulation Thickness – 1.0mm (Nominal) vii) Inner Sheath Minimum Thickness – 0.3mm viii) Outer Sheath Minimum Thickness – 1.40mm ix) Nominal size of Armoured Wire/Strip – 4x0.8mm x) Approximate O.D. – 22mm Maximum d.c. Resistance at 20 Deg. C – 1.91 ohm/km The work shall be executed to the entire satisfaction of Engineer-in-Charge. — Qty: 250 Mtr
Supply & Laying of DWC pipe 51/63mm with hand bockey:- DSR 14.15.1 (75 cm below) — Qty: 50 Mtr
Supply & Laying of DWC pipe 51/63mm without hand bockey:- DSR 14.16.1 (75 cm below) — Qty: 70 Mtr
Minor Repair of Cement Bollarrd/CC Collar. Minor Repair of Cement Bollarrd/CC Collar (with Red Paint ) with Apex and all the necessary items for repair i.e. sand and cement and curing of CC collar after complete in all respect to the entire satisfaction of Engineer-in-charge. — Qty: 30 Nos.
Repair of pedestal covers of size 1200X900X350 mm and 900X600X350 mm with Hinges, Welding and Labour at site all T&P for door as requried to the best satisfaction of Engineer in charge. — Qty: 5 Nos.
Supply & Erection of steel tubular pole 410 SP-27 conforming to IS-2713-1980, (Part-I & II) having overall length of 9 Meter and welded in 3 steps and having approximate Wt. 108 Kgs. With the following specifications:- a) The poll shall have cross-sectional length of 5.00, 2.00, 2.00 Mtrs. b) The outside dia and thickness shall be114.3x5.40mm, 88.9x4.85mm and 76.1x3.25mm. c) The pole shall be erected 1.50mtrs. Below the ground level in 8” internal ready made RCC muff. d) The gap between the pole and the muff shall be filled with the cement concrete 1:2:4. The cost includes all labour and material including carriage to the site of work. e) The bottom portion of the pole shall be painted with two coats of black paint after removing the dust/rust. — Qty: 1 No.
SUPPLY & ERECTION OF G.I.PIPE BRACKET 5 FEET O/H DOUBLE ARM:- Supply and Erection of 5’ over hang bracket Double Arm made of G.I. pipe medium class ISI Marked with the following specifications of Make Tata/ Jindal/ Hissar or Ravindra. The work shall be executed to the entire satisfaction of engineer-in-charge. 1. The bracket shall be made from 2” dia G.I. pipe with an angle of inclination of 105 degrees to the vertical. 2. The 2” dia G.I. pipe shall be welded to 3” dia G.I. pipe canopy at a distance of 2” from top end & top end of canopy shall be covered with 14 GMS sheet to avoid entry of rainwater in Steel Tubular Pole. 3. The bracket shall be slipped over the top section of the steel tubular pole and fixed with 2 Nos. of ½” dia nuts and bolts suitable to hold the pipe absolutely tight in positions. 4. A stiffnee plate of triangular shape of 14 GMS sheet of 6 — Qty: 1 Nos.
G.I. Earth pipe electrode without salt/ Charcoal: DSR 5.2/2022 Supply and laying of earth electrode made out of ISI marked 'B' class earthing with G.I. earth pipe 3 mtr long, 40mm dia including accessories, G.I. pipe electrode shall be cut tapered at the bottom, and provided with holes of 12mm dia, drilled not less than 7.5 cm from each other upto 2 Mtr. of length from bottom (without charcoal or coke and salt). The earth electrode shall be laid in ground after boring as per CPWD specifications complete in all respect and to the entire satisfaction of the Engineer-in-charge. — Qty: 1 Nos.
P/F 6 SWG GI earth wire in pipe: DSR 5.12/2022 Providing & laying earth connection from earth electrode with 6 SWG dia G.I. wire in 15 mm dia G.I. pipe from earth electrode, as required. — Qty: 3 Mtrs.
PAINTING & NUMBERING OF POLES 7.5/9 MTR. LONG:- (Without Snowcem) Painting of poles above ground level with two coats of paint of Silver Colour Nerolec/ Asian/ ICI duly approved by the Engineer-in-charge. The pole surface should be cleaned well by removing dust/ rust & other depositions & smoothened with the sand paper/Iron brush & proper filling be made before painting. For numbering of poles the base should be painted with yellow and the number should be written in black letters of 3” in length. The cost includes painting of Danger Sticker in Existing Street Light Poles. The Danger sign's shall be written on each pole on it's two sides with red paint on yellow base to be show to warning about hazard as threats which are essential to safety for General Public. The job includes all type of petty material require to complete the job to the entire satisfaction of Engineer-in-charge. — Qty: 1 Nos.
Providing and fixing of pad lock to be fixed in existing panel cover. The job also includes the cost of painting of the complete pedestal to the entire satisfaction of Engg. in charge. — Qty: 50 Nos.

1 tender document(s) available — sign up to download.

Related tenders

SUPPLY OF V.F TRANSFORMER OF RATIO 470:600 OHMS (CYLINDER TYPE) — Electrical Equipment & Supplies · Madhya Pradesh
Handheld Rechargeable Pocket Torch — Electrical Equipment & Supplies · Madhya Pradesh
Procurement of Digital Dial Indicator and Stainless Steel Flexible Magnetic Base stand — Electrical Equipment & Supplies
Contact Lever Complete of Tap Changer to M/s. REPL's Pt. No. - S-2506 or to RDSO's Drg. No. - SKEL-4659 (Alt. - 1) — Electrical Equipment & Supplies · West Bengal
LED Flasher Relay — Electrical Equipment & Supplies
Electrical Windscreen Wiper Motor for Automobiles — Electrical Equipment & Supplies · Uttar Pradesh
Lighting Box (Flasher For Police Vehicles) — Electrical Equipment & Supplies · Gujarat
LED Luminaire For Floodlight Conforming To IS 10322 (Part 5/Section 5) (V3),Self Ballasted LED Lamp — Electrical Equipment & Supplies · Madhya Pradesh