KMC/WS/JOKA/18/2026-27

Kolkata Municipal Corporation · Kolkata, West Bengal · Civil Works & Infrastructure · open

Key facts

Tender value: ₹2.7L
EMD: ₹6K
Published: 05 Nov 2026
Closing date: 25 Nov 2026
Status: open
Status as of: 09 Nov 2026 00:00 UTC
Department: Water Supply
Office: Water Supply

Description

Leakage repairing work on 600 mm dia transmission main, 350 mm dia rising main and 300 mm dia reserve main, including M.S. work and air valve repairs at Prantik Road, Churial Bridge, in front of St. Andrew School and Kalitola in Ward No. 143, Borough XVI, Kolkata.

Eligibility & requirements

Startup relaxation: No
MSE relaxation: No

New to these terms? Read how tender eligibility criteria work.

Commercial terms

Bid type: Percentage
Make in India (MII): No
MSE preference: No

Line items (26)

CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.3 M.S. Pipes 2.3.1 Gas cutting of M.S. pipes and/or M.S. plates of different thickness all complete as per specification and direction of the Engineer-in- Charge. Thikness in mm 5mm to 8mm thick plate — Qty: 14.8 MTR
BUILDING WORKS (F) STRUCTURAL STEEL WORKS, GRILLS, GATES ETC. B. REPAIRING 2. Welding in M.S. structural work with gas or electric: (a) Tack weld — Qty: 60 PNT
CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.3.9 LowerIng M.S pipes & specials in trench up to a depth of 3.00 metre below G.L, laying and jointing the same inside the trench / over ground by means of electric arc welding using standard electrodes as per l.S. specification, all complete as per direction of the Engineer-in-Charge. [The Engineer-in-Charge shall approve the electrodes for arc welding before use. (For laying over ground. the rates shall be reduced by 10% and that is inclusive of holding arrangements) ] — Qty: 1.5 %MT
STEEL PLATES(E 250 CONFORMS TO 2062-2006), A- 6TO 10MM — Qty: 0.1433096 MT
CHAPTER - I [ SUPPLEMENTARY ] EXCAVATION, SHORING, BAMBOO PILING, FENCING & SIGN BOARD, LIGHTING & SIGNALING AND SITE CLEANING ETC. 1.13 Hire & labour charges for diesel generating set for lighting including fuel,300M wire, 11 points with 200 Watt bulb with post for hanging & maintaining the same for day & night for the period. — Qty: 4 DAY
(C) III: Labour Rate for Sanitary and Plumbing 5.Plumbing Helper NOTE:The above rates are exclusive of 10 % profit and 1% Labour welfare cess, which would be admissible to the Contractor, but contractual percentage will not be applicable on the above rates. Page 113 of 124 — Qty: 8 EA
CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.3.3 Field welding of M.S. plate by means of electric arc welding as per releventIS specification using standard electrodes including edge preparation and charges of deployment of electric generator set with fuel, lubricant, and allother tools and plants all complete as per specification and direction of Engineer-in-Charge.[Engineer-in-Charge shall approve the electrodes for arc welding before use ]Throat thickness in mm 8mm — Qty: 32.07 MTR
CHAPTER - I [ SUPPLEMENTARY ] EXCAVATION, SHORING, BAMBOO PILING, FENCING & SIGN BOARD, LIGHTING & SIGNALING AND SITE CLEANING ETC. 1.10 Hire and labour charges for coir rope fencing 25 mm dia rope single on 120 mm dia bamboo posts 1.40 m above G.L and 600 mm below G.L, 1.50 m apart including digging holes complete. — Qty: 12 MTR
CHAPTER - VII MISCELLANEOUS ITEMS Dewatering by pumps including all leads, lifts and making all arrangements of disposal. where continuous flow of water from a source other than natural or ground water is encountered in case of emergency maintenance works related to leakage. breakage and making wet connections. [Note ;- In case of any other situation demanding such emergency dewatering. use of this item is to be approved by the Superintending Engineer/Tender Accepting Authority. This item shall be executed on the specific direction duly supported by proper clarification of the E.I.C. who will be satisfied in absolute discretion that such work has not been necessitated due to any natural source of water or any fault of the Contractor] — Qty: 232 HPH
CHAPTER - I [ SUPPLEMENTARY ] EXCAVATION, SHORING, BAMBOO PILING, FENCING & SIGN BOARD, LIGHTING & SIGNALING AND SITE CLEANING ETC. 1.14 Signalling arrangement at both sides of site to avoid any accident during working period 4 nos. red flags during sunlight at 4 corners and 2 nos light (lamp) in other than sunlight. — Qty: 18 DAY
CHAPTER - I [ SUPPLEMENTARY ] EXCAVATION, SHORING, BAMBOO PILING, FENCING & SIGN BOARD, LIGHTING & SIGNALING AND SITE CLEANING ETC. 1.2 Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete.(Payment to be made based on the basis of measurement of finished quantity of work.(a) With earth obtained from excavation of foundation — Qty: 26.26 %M3
CHAPTER - IV INSERTING PIPES AND SPECIALS Inserting M.S pipe and/or special up to a length of 5.50 metre in the gap formed by cutting existing M.S main, bailing out of water from the trench due to normal seepage if any. providing temporary support including gas cutting all complete as per specification and direction of the Engineer-in- Charge.[The Engineer-in-Charge shall approve the electrodes for arc welding before use and the cost of ere welding of joints shall be paid extra as per the relevant item of the Schedule of Rates]] Diameter in mm 450/500 — Qty: 1 MTR
CHAPTER - VIII SUPPLYING OF MATERIALS Supply of M.S. Flange (slipper type) as per IS-6392 TABLE 17 Thickness - 20mm -22mm NB Diameter in mm 350 — Qty: 2 EA
CHAPTER - VII MISCELLANEOUS ITEMS Supplying, fitting and fixing of C.I. Mechanical flexible Flange Socket Tailpiece suitable for making flanged connection with the plain barrel of C.I.Spun Pipes (as per IS : 1536) and D.I. Pipes (as per IS : 8329). The Tailpieces to be supplied complete with Sealing Rubber Gasket of EPDM quality (IS:5382/1985 Type-4), Cast Iron Follower Glands and Mild Steel Nut Bolts (Zinc Coated). The whole assembly should be mechanically and hydraulically tested to the provisions as laid down in IS: 1538. Fitting and fixing should be in proper position with proper care of main pipe line for leak proof condition. Diameter in mm. with minimum barrel length in mm 350mm with length 150mm — Qty: 1 EA
CHAPTER - VIII SUPPLYING OF MATERIALS F. MS FLANGE 8.17 Supply of M.S. Flange (slipper type) as per IS-6392 TABLE 17 Thickness 12mm NB Diameter in mm 100 — Qty: 1 EA
CHAPTER - VII MISCELLANEOUS ITEMS Repair of Air valve by supplying ebonite and- rubber ball. gasket. nuts and bolts with washers and labour all complete Diameter in mm 100 — Qty: 3 EA
CHAPTER - VIII SUPPLYING OF MATERIALS 8.12 Cast iron kinetic double orifice type air release valve having small orifice elastic ball resting on gun metal orifice nipple large orifice vulcanite ball seating on moduled seat ring, valve with built-in-Kinetic features, isolating sluice valve mounted in horizontal position and operated by a metre wheel gearing:inlet faced and drilled to IS 1538 Table 4 & 6. valve suitable for maximum working pressure of 10 kg/CM2 Diameter in mm 80 — Qty: 1 EA
CHAPTER - I [ SUPPLEMENTARY ] EXCAVATION, SHORING, BAMBOO PILING, FENCING & SIGN BOARD, LIGHTING & SIGNALING AND SITE CLEANING ETC. 1.1 Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm. — Qty: 26.25 %M3
STRUCTURAL STEEL(MS) ANGLES, JOIST, CHANNEL, FLATS(E 250 CONFORMS , IS: 2062 & 808)UPTO 200 MM SIZE — Qty: 0.0534 MT
CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.3.5 Fabricating M.S. pipes of different diameter in shop out of 8mm to12mm thick M.S plates supplied depart-mentally, cutting the plates to exact size & shape by gas cutting device and/or by adopting any other approved type of mechanical means, bending the same in true curvature by template and rolling machine of approved design including proper marking, levelling joints followed by electric arc welding as per relevant I.S. specification - longitudinal and circumferential, as necessary, usiug standard electrodes including edge preparation, electricity charges and hydraulic testing of the fabricated piece all complete as per speci-fication and direction of the Engineer-in-Charge. [The Engineer-in-Charge shall approve the electrodes for arc weldingbefore use.]a) Diameter from 450 mm & upto 600 mm.i) 8mm thick plate. — Qty: 0.1433096 MT

1 tender document(s) available — sign up to download.

Related tenders

UNDER FRAME (LS & LWS PP) — Civil Works & Infrastructure · Tamil Nadu
Macdamization of road surface at syed Kamalud din Colony wanganpora Eid gah Near UPHC from h/o Ali Mohd upto h/o Nasir Khalel. — Civil Works & Infrastructure · Jammu and Kashmir · ₹15.0L
Operation of supply valves for the distribution pipe line for piped scheme Babaichya and Narwar with associated works, under jurisdiction of sub division rural, District Rural Division Ajmer (Excluding GST) — Civil Works & Infrastructure · Rajasthan · ₹3.3L
Construction of Mali Hut at Bimalnag Nursery under CAMPA CAT RATTLE for the year 2026 27 — Civil Works & Infrastructure · Jammu and Kashmir · ₹16.7L
CONSTRUCTION OF TOILET BLOCK IN SANOUR CITY — Civil Works & Infrastructure · Punjab · ₹9.1L
Repair of street and drainage in w.no.2 — Civil Works & Infrastructure · Punjab · ₹25.0L
Repair and renovation of University Library Building at GADVASU, Ludhiana. — Civil Works & Infrastructure · Punjab · ₹9.5L
P/F Interlocking Tiles St. Baba Jora EO Gurudwara Street Ward No.07 — Civil Works & Infrastructure · Punjab · ₹3.4L