Complete Restoration work of CHEP-I and accessories as per detailed scope of work mentioned in SBD
Jammu & Kashmir State Power Development Corporation (JKSPDC) · Udhampur, Jammu and Kashmir · Repair, Maintenance & AMC Services · open
Key facts
- Tender value: ₹27.4Cr
- EMD: ₹55.0L
- Published: 29 Oct 2026
- Closing date: 24 Nov 2026
- Status: open
- Status as of: 09 Nov 2026 02:43 UTC
- Department: Generation Wing
- Office: Generation Division Udhampur
Description
Turnkey restoration of four units (Units I–IV) of the 23.3 MW Chenani Hydro Electric Project Stage-I, including turbines, runners, MIVs, generators and auxiliaries, control and protection panels, instrumentation, hydro-mechanical works, lubrication, HPU and cooling systems. The contractor must restore all four units and ensure they are connected to the bus and generating power.
Eligibility & requirements
- Startup relaxation: No
- MSE relaxation: No
New to these terms? Read how tender eligibility criteria work.
Commercial terms
- Bid type: Two Packet Bid
- Evaluation: Item wise
- Make in India (MII): No
- MSE preference: No
Line items (57)
- 2 — Qty: 4 5
- Turbine & Associated Components Runner including Buckets Replacement of old and Supply and Installation of new speed sensors along with connecting cables compatible with existing associated components and other allied works — Qty: 4 set
- Buckets: • Sandblasting, primer coating, and finishing with an epoxy paint with marine grade be carried out on entire installation for the effective refurbishment and long-term protection. • Proper surface preparation is ensured before coating performance — Qty: 4 set
- Runner Housing, Turbine chamber and Shield Plate Refurbishment of runner housing including sand blasting and Epoxy painting with marine grade inclusive of all material and allied works — Qty: 4 set
- Replacement of old and Supply and Installation of new of existing MS Shield Plate and nut bolts with new one of SS material and application of High Velocity Oxygen Fuel (HVOF) Coating on new Shield plates only — Qty: 4 set
- Replacement of old damaged seals and Supply and Installation of new seals ( NBR Shore 70) and packing with new rubberized cork sheets and welding wherever required — Qty: 4 set
- Replacement of old and Supply and Installation of new nut bolts . Note: During refurbishment /repair/ replacement, Utmost care shall be taken for civil associated structures and same be repaired in well manner accordingly wherever required — Qty: 4 set
- Drive End (DE) Bearing Replacement of existing bearings with new one and other allied works including supply, Installation, alignment, rechecking and allied mandatory tests of shafts, bearing housing and bearing covers and insitu minor repairs to shaft (if reqd after removal of bearings). Complete housing along with bearing to be replaced — Qty: 4 set
- Brake Jet System Replacement of old and Supply / Installation of new of complete braking system and its integration with the existing OPU system including all piping works, auxiliaries, other allied associated works and integration with the digital governor system. The nozzle for brake jet is to be replaced. i. The hydraulic valve utilized for turning the water jet on/off shall be replaced along with the Supply installation testing and commission of new hydraulic pipeline from the OPU. ii. The SITC of complete braking system and its integration with the OPU system & integrated with the digital governor system and same be taken up before restoration of the machines. iii. Restoration of brake jet system be interfaced and integrated with Governor for all 4 units. iv. Supply of other auxiliaries like piping and other details of braking system shall be compatible with the system v. Replacement of damaged brake jet system with new one, compatible with the system. — Qty: 4 set
- vi. In addition to above, at least 1 no. sets be kept as spare to tackle any eventuality in future. Nozzle and operating mechanism, directional/solenoid valves, hoses with unions, operating valves as installed in new brake jet system all sensors as installed in the new brake jet system along with associated gauges, filters, gasket, seal etc to be supplied as spare. — Qty: 1 set
- Nozzle Seat Ring, Needle Tip (Bottom & Upper side) and Deflectors To enhance the life of nozzle seat ring, it is recommended to replace all the parts of brass material of this equipment and consider using stainless steel material, with HVOF coating instead of brass. Additionally, applying HP-HVOF coating to the needle tip is recommended for improved durability and erosion resistance. Replacement of Existing 2 (two ) Nos. Nozzles, Seat rings 2 no's and Deflectors 2no's including Deflector rod and connecting pins in each machine with supply and installation of new one of SS material and HVOF coating thereof. Setting Alignment and other allied works. SS material should specifically be of ASTM A240 UNS 41500 with HVOF or F6NM (13 Cr-4Ni) with HVOF or X3CrNiMo13-4+QT780 with HVOF or Gx4CrNi13-4+QT780. Replacement of Complete nozzle assembly (excluding housing) with HVOF Coating wherever applicable. — Qty: 4 set
- Overhauling of existing 2nos Nozzle servo motors and Deflectors Servomotor including replacement of all the NBR shore 70 seals, gaskets, transducers/ Sensors with compatible cabling works. Replacement of 2 No deflector servomotor transducer for each machine. Replacement of 2 No nozzle servomotor transducer for each machine. Setting, Alignment & other allied works be checked again before restoration of the units. — Qty: 4 set
- Cooling water System: Dismantling of existing Cooling water system. Design, supply installation testing and commissioning of 1W+1S CW scheme (mechanical seal type) with dual inline filters and separators with back flushing including other allied piping of SS material. Pumps must operate in automatic mode with alternating operation logic to ensure redundancy. Provide discharge piping for silt flushing and proper drainage system connection. Non-Return Valves (NRV ball type)-8 No (To prevent backflow in pipelines). Isolation Valves (Butterfly/Gate) for maintenance and flow control. Dismantling of old choked water re-coolers. Design, Supply, Installation, testing and commissioning of new water re-Coolers in the tailrace of the power house including associated pipelines( SS material) and other allied works including required associated works like tapping of connection, PRV and other items — Qty: 4 job
- Main Inlet Valve (MIV) & Bypass Valve Over hauling of MIV Spherical Valve & By pass valve including all the seals, bushes and necessary accessories along with piping Compatible with the existing system and interfacing with the digital governor panel — Qty: 4 job
- Replacement of old & SITC of New OPU for MIV & By pass valve -along with piping etc compatible with existing system and interfacing with governor panels — Qty: 4 set
- Replacement of Old & SITC of new MIV servomotor, bypass mechanism, gate valve, seals, bushes, Transducers and other allied works. The whole mechanism shall be integrated and operatable through HPU of that particular unit. Or If the bidder proposes to replace the existing complete MIV assembly with the supply, installation, testing and commissioning of a new assembly comprising the MIV, OPU, Spherical valve, Bypass valve, all seals, bushes and all other necessary allied components and works, they may do so. However, all the components removed from the existing MIV assembly shall remain the property of JKSPDC — Qty: 4 set
- Digital Governor panels and OPU Supply and installation of heat exchanger system (complete) for governor OPU along with allied piping work. — Qty: 4 set
- Up gradation of Digital Governor by way of retrofitting the obsolete existing governor PLC, AI, AO, DI, DO with new compatible modules( including supply, installation, testing and commissioning), (HIPASE/SICAM/HyCon) based control systems that should be compatible with existing system, including all allied works such as system integration, wiring modifications, software configuration, testing & commissioning and replacement of defective components like relays, annunciator display LEDs and other associated accessories. Installation of new field instruments like pressure switches, feedback transducers, speed sensors, proximity switches etc. — Qty: 4 job
- Complete overhauling of Governor OPU by way of replacing all the proportional valves, check valves, Filters, solenoid valves, gauges, regulating valves, manifolds, transducers, piping, seals, gaskets etc. The job also includes overhauling of Governor pumps and other allied works. or The contractor may supply new Governor OPU of reputed make however, the old replaced OPU shall remain the property of JKSPDC — Qty: 4 job
- Replacement of piston accumulator along with associated components. — Qty: 4 job
2 tender document(s) available — sign up to download.
Related tenders
- KANDRI/ENGG/PUR/2026-27/ 1909 — Repair, Maintenance & AMC Services · Maharashtra · ₹1.4L
- AMC of Cooling Equipments of NPM — Repair, Maintenance & AMC Services · Odisha · ₹6.5L
- Repair and Maintenance Jobs in Unloading and Screening Area of RMHP — Repair, Maintenance & AMC Services · Odisha · ₹53.2L
- Service Engineering Visit for Maintenance of Van Mounted Cable Fault Locator — Repair, Maintenance & AMC Services · Odisha · ₹2.7L
- Emergency Visit for ABB Drives and Automation System — Repair, Maintenance & AMC Services · Odisha · ₹58.4L
- Cylinder Maintenance and Handling Service — Repair, Maintenance & AMC Services · Gujarat · ₹3.1Cr
- THREE YEAR ARC FOR SUPERVISION OF OVERHAULING/SERVICING OF M/S INSTRUMENTATION LIMITED (IL) VALVES AT BPCL KOCHI REFINERY — Repair, Maintenance & AMC Services · Kerala
- THREE YEAR ARC FOR SUPERVISION OF OVERHAULING/SERVICING OF M/S SAMSON VALVES & POSITIONERS, BPCL KOCHI REFINERY — Repair, Maintenance & AMC Services · Kerala